- #INTEL I210 DRIVER PARAMETERS DRIVERS#
- #INTEL I210 DRIVER PARAMETERS DRIVER#
- #INTEL I210 DRIVER PARAMETERS SOFTWARE#
4 rx queue(s), 4 tx queue(s)ĭoes anyone know what could be going wrong here and how I can get these NICs working? If it's at all possible to do that without manually compiling kernels or drivers, I would prefer that. igb 0000:02:00.0: Intel(R) Gigabit Ethernet Network Connection igb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection igb: Copyright (c) 2007-2013 Intel Corporation.
#INTEL I210 DRIVER PARAMETERS DRIVER#
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.3-k
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0Įth1 Link encap:Ethernet HWaddr ac:22:0b:8b:30:a8īut for some reason, I can't actually use them for anything: # ifconfig eth0 upĬannot get device settings: No such deviceĬannot get wake-on-lan settings: No such deviceĭmesg doesn't seem to have any interesting output from the responsible igb driver: # dmesg | grep igb RX packets:0 errors:0 dropped:0 overruns:0 frame:0 The ethernet interfaces do show up in ifconfig -a: # ifconfig -aĮth0 Link encap:Ethernet HWaddr ac:22:0b:8b:30:a7 Ii linux-image-amd64 3.10+52~bpo70+1 amd64 Linux for 64-bit PCs (meta-package) The server is running Debian wheezy with the most recent backports kernel: # cat /etc/debian_version It has two onboard Intel NICs: # lspci -nn | grep EthĠ1:00.0 Ethernet controller : Intel Corporation I210 Gigabit Network Connection (rev 03)Ġ2:00.0 Ethernet controller : Intel Corporation I210 Gigabit Network Connection (rev 03) To determine whether your driver type requires that you store information under specific registry keys, see the sections of this documentation that discuss your driver's device type by using the table of contents.I have a server with an Asus P9D-I mainboard. Your driver's INF file can contain INF AddReg directives that set registry values under the hardware key using INF DDInstall.HW sections. Your driver can call WdfFdoInitOpenRegistryKey and WdfDeviceOpenRegistryKey to open a device's hardware key. 'The e1000 driver is the one that can run the I2xx intel Ethernet Controllers' - except I210 and I211, according to this README. Settings related to the hardware (such as interrupt settings) can be stored here by drivers.
When a driver stack informs the Plug and Play (PnP) manager that a device is connected to the system, the PnP manager creates a hardware key for the device.
#INTEL I210 DRIVER PARAMETERS SOFTWARE#
Your driver's INF file can contain INF AddReg directives that set registry values under the software key using INF DDInstall sections. Your driver can call WdfFdoInitOpenRegistryKey and WdfDeviceOpenRegistryKey to open a device's software key. The system stores information about each driver under its software key. Subsequently, the driver can obtain the path by calling WdfDriverGetRegistryPath.Ī driver's software key is also called its driver key. Your driver must pass this path to WdfDriverCreate. Because the image is compressed, the stride parameter for the k4aimaget is not. When the system calls your driver's DriverEntry routine, it passes the driver a path to the driver's key in the appropriate Services tree. 265 Main 10 Profile is supported in 7 th generation Intel processors. The subkey for the driver always uses the driver's service name, even if the driver binary's file name differs from the service name. For User-Mode Driver Framework (UMDF) drivers, this key is located in the HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\WUDF\Services tree, under the driver's service name.
For Kernel-Mode Driver Framework (KMDF) drivers, this key is located in the appropriate Services tree for the driver. The driver's Parameters key can contain configuration information for your driver and can be accessed by calling WdfDriverOpenParametersRegistryKey. Your driver might access the following registry keys:
#INTEL I210 DRIVER PARAMETERS DRIVERS#
Drivers typically use a set of system-defined registry keys to store or access driver-specific or device-specific information.